What killed it, well after reviewing some PS4 gameplay I noticed that it was having audio issues, like it would allow some sounds but not all. It was almost as if it was receiving a 5.1 audio output but was missing the centre channel. Even though the PS4 was set to stereo.
After trying various cables, configs, and boxes. I narrowed it down to this box. Not sure what killed it, whether it’s just old, or that it’s been powered on for over 5 years straight. But its long service will never be forgotten in the hours of Netflix and Disney Plus it passed through to my recorder.
I see corrosion/deposits by those two leds and the hdmi… rinse it with vinegar, then DI water, then 90% alcohol. See if that doesn’t bring it back to life once it’s fully dry. You also might have to reflow the solder though.
Just curious since you clearly know a lot about this stuff: What are your thoughts on the heat sinks being a part of the issue? Is there a decent chance the device could benefit from replacing whatever adhesive/paste was used to attach them? Or is that even doable?
It depends on how much heat it’s actually making, but maybe if the factory job done was crappy. It’s probably thermal adhesive though which is harder to remove.
They can work, though I’m always reluctant to suggest using them, unless you have one that you can spare without worry of ruining the oven (offgassing from components/PCB/flux), the other problem is ovens can be a lot more variable in temperature than you’d think, and in this scenario where it may even be the chips showing their age, subjecting them to very high temperatures isn’t recommended.
Honestly when I bought a small £20 heatgun (smaller than the type you’d use to strip paint), I was kicking myself for not having bought one sooner, they make surface mounted components an absolute breeze Vs using a soldering iron.
The one exception for using ovens is if you’re having to do an intricate board with hundreds of components, then I’d suggest buying a small/medium toaster over, and an oven thermometer for more accurate readings.
If you have a hot air rework station, that’s one way. Because then it is temp and flow controlled and you can choose a suitable nozzle and direct heat to small spots.
You are not logged in. However you can subscribe from another Fediverse account, for example Lemmy or Mastodon. To do this, paste the following into the search field of your instance: !piracy@lemmy.dbzer0.com
⚓ Dedicated to the discussion of digital piracy, including ethical problems and legal advancements.
I see corrosion/deposits by those two leds and the hdmi… rinse it with vinegar, then DI water, then 90% alcohol. See if that doesn’t bring it back to life once it’s fully dry. You also might have to reflow the solder though.
Good call. And better than 90% isopropyl is Anhydrous alcohol.
A neighborhood laptop repair shop could probably do all these steps for you, too.
I have another in the setup thats working, but I’ll probably hold onto it though if I can fix it as easily as you say
Just curious since you clearly know a lot about this stuff: What are your thoughts on the heat sinks being a part of the issue? Is there a decent chance the device could benefit from replacing whatever adhesive/paste was used to attach them? Or is that even doable?
It depends on how much heat it’s actually making, but maybe if the factory job done was crappy. It’s probably thermal adhesive though which is harder to remove.
How would you reflow the solder?
With an iron? Or a heat gun? What would be the best approach for something like this with lots of tiny surface mounts?
Not who you asked but 100% use a narrow heat gun, no question; it saves so much time alongside not accidentally bringing connectors
Would an oven work?
They can work, though I’m always reluctant to suggest using them, unless you have one that you can spare without worry of ruining the oven (offgassing from components/PCB/flux), the other problem is ovens can be a lot more variable in temperature than you’d think, and in this scenario where it may even be the chips showing their age, subjecting them to very high temperatures isn’t recommended.
Honestly when I bought a small £20 heatgun (smaller than the type you’d use to strip paint), I was kicking myself for not having bought one sooner, they make surface mounted components an absolute breeze Vs using a soldering iron.
The one exception for using ovens is if you’re having to do an intricate board with hundreds of components, then I’d suggest buying a small/medium toaster over, and an oven thermometer for more accurate readings.
If you have a hot air rework station, that’s one way. Because then it is temp and flow controlled and you can choose a suitable nozzle and direct heat to small spots.
I’ve reflowed a raspberry pi 0w with a camping stove and a thermometer. As long as there aren’t any components on the other side of the pcb, it might work.
Edit: here’s an old photo. Thing still works, many months later
This.
I would absolutely try cleaning the board.
I would also spend $8-20 for a new one before I tried to DIY solder reflow various SMD caps.