Some routine maintenence and losing your balance while holding a hard drive and ripping the cord out breaking the retainer for the connectors… 4tb Samsung ssd RIP
I did this to a PNY drive once and they RMAd it for me! I was up front and said it was 100% my fault and I had already had it for a few years. If you’ve got a laptop that has a mounted slot you can probably slide it in to get any data you need off of it
It’s really easy. I have be soldering to repair my own guitars since I was like 12. Watch an instructional video on the internet, practice with some spare wires and circuit boards. You can learn in an hour or two.
Problem for most people isn’t going to be the act of soldering. It’s going to be acquiring a soldering station and some solder to work with. If you intend to use it multiple times it’s not bad at all. For a one-and-done situation it’s best to just pay someone else to do it with their equipment or buy a new SSD entirely.
I mean, maybe. When I moved out of my parents house and didn’t have access to their set up, I paid like $50 for a decent soldering iron with an on/off switch, a stand, and a heat dial. And $5 for some solder. I feel like it will pay for itself in just one use. And once you have one, you’ll realize all things you can fix on our own instead of replacing it or paying someone to fix it.
Having all pins present, I wouldn’t be surprised if the drive still gets detected while bending a SATA cable back juuuuuust right so its connector makes contact with the pins.
I’ve used computers for years like that, also these card edge connectors are pretty standard and can be easily replaced by anyone who can do basic soldering.
Seconded. If OP lives anywhere near a city, there’s probably an electronics repair shop within reach that would solder on a new connector for less than the cost of a new SSD.
You are not logged in. However you can subscribe from another Fediverse account, for example Lemmy or Mastodon. To do this, paste the following into the search field of your instance: !gaming@beehaw.org
From video gaming to card games and stuff in between, if it’s gaming you can probably discuss it here!
Please Note: Gaming memes are permitted to be posted on Meme Mondays, but will otherwise be removed in an effort to allow other discussions to take place.
Some routine maintenence and losing your balance while holding a hard drive and ripping the cord out breaking the retainer for the connectors… 4tb Samsung ssd RIP
My sympathies that is painful.
I did this to a PNY drive once and they RMAd it for me! I was up front and said it was 100% my fault and I had already had it for a few years. If you’ve got a laptop that has a mounted slot you can probably slide it in to get any data you need off of it
ymmv with this, but it looks like a mostly ok jank fix. Those adapters won’t be expensive. https://youtube.com/shorts/yVV9Ip92ffg
Steady hand with a soldering iron and that could be salvaged, good luck!
Hey Alexa, how 2 soldier
It’s really easy. I have be soldering to repair my own guitars since I was like 12. Watch an instructional video on the internet, practice with some spare wires and circuit boards. You can learn in an hour or two.
Problem for most people isn’t going to be the act of soldering. It’s going to be acquiring a soldering station and some solder to work with. If you intend to use it multiple times it’s not bad at all. For a one-and-done situation it’s best to just pay someone else to do it with their equipment or buy a new SSD entirely.
I mean, maybe. When I moved out of my parents house and didn’t have access to their set up, I paid like $50 for a decent soldering iron with an on/off switch, a stand, and a heat dial. And $5 for some solder. I feel like it will pay for itself in just one use. And once you have one, you’ll realize all things you can fix on our own instead of replacing it or paying someone to fix it.
Like I said, it comes down to if you’re doing it once or if you intend to use the soldering iron again in the future. $55 is a lot for a once-off use.
Yeah, but how much does paying someone for the repair cost? I can’t imagine it’s less than that.
First step, you need to enlist. A soldiering iron will be issued to you, there will be many like it, but that one will be yours…
I’m doing my part!
You might still be able to use it if you carefully superglue back the plastic part.
A more permanent fix would be to replace the SATA connector and solder a new one by someone with the proper skillset.
The important parts are still in good shape, don’t throw it away!
Having all pins present, I wouldn’t be surprised if the drive still gets detected while bending a SATA cable back juuuuuust right so its connector makes contact with the pins.
I’ve used computers for years like that, also these card edge connectors are pretty standard and can be easily replaced by anyone who can do basic soldering.
Considering this is the data portion of the SATA connector I’d be worried about data integrity all the time 😬
Seconded. If OP lives anywhere near a city, there’s probably an electronics repair shop within reach that would solder on a new connector for less than the cost of a new SSD.
Hmmm I could risk it and try the hero move here…
If it’s dead then it’s no risk, right? Afterwards it’s either working or still dead.
Hopefully what’s on the disk could be salvaged from a computer shop or something. 4tb SSD though… Ouch.
Just my steam and GOG library, nothing valuable besides the hardware :/
If you’re assuming it’s trashed anyway may as well try to fix it.
I can fix that for you if you ship it to me